I finished stitching the flowers and leaves and filled in the green leaf areas. I used an overdye for the leaf area and stitched one area at a time. I thought I would go from side to side across the entire piece but I did not like the look and so I frog stitched it out and tried one area at a time. I tried to get each area alike but when I was finished I think the two left are similar and the two right are similar…oh well, it is stitched.
Up close I am not impressed with the flower area but as you get some distance to the piece I do like the look and since I have a finishing idea in mind (more about this later) I think it will be fine. And anyway as my friend says, “If your close enough to my piece to see my mistakes; you are too close.” So if you are going to be this close to the piece you are too close.
After I finished the flowers I went back and filled in the bunnies and since I had the white thread out I got carried away and stitched the bunny tails in Turkey work. Mom’s tail has longer loops than baby bunny. I thought at first I would trim and brush Mom’s tail but I like the different lengths and think I will leave them both loopy. I probably should have waited until I finished the back ground but, oh well…
I have started the background and am using ThreadworX’s floss. I am puddling the stitches, I really like this technique for overdyes. Puddling keeps thread from developing a striped effect like you can get when you stitch horizontally, vertically or diagonally. The only thing I have found that I have to watch is making sure I don’t develop huge areas of one color. Some overdyes have a tendency to have larger areas of one color than another and if not careful you can develop large areas of one color. Helpful hint: cut out large areas of one color.
Last fall I showed you how to stitch the puddle method with a continuous uncut overdyed thread, like Watercolours (https://sudukc.wordpress.com/2013/10/01/overdye-puddle-stitching/). With ThreadworX it is a slightly bit different because these threads are cut into given lengths of thread. When you open a skein of ThreadworX’s and lay it out there will be an “A” end and a “B” end and it may appear the same as an overdye that has been cut from an uncut overdyed thread (like Watercolours). The difference is that ThreadworX’s threads are consistently similar where Watercolours may vary a bit as the skein is used because of the dying method.
When I puddle stitch I randomly pull ply and stitch. I do keep “A” ends together and “B” Ends together; if you don’t then you will get a blended effect and that is another way to stitch with overdyes. For my purposes in this design I am keeping the “A” ends and “B” ends together in the needle…BUT I am randomly deciding which ends (“A” or “B” ) goes into the needle.
Example: With one strand of thread, using 2 ply in the needle to stitch, there are three stitching lengths in a thread per strand: 2 ply A-B, 2 ply A-B, 2 ply A-B (Oh I knew those math classes in school were for something…remember those teachers that said you would use these principles in life?). I divide these threads and place them in three needles 2 ply A-B, 2 ply A-B AND 2 ply B-A. (it could have been any combination…remember that math week on variables…this is an applied use and for all you math geeks out there…it is 5 choices.) Then I pick a needle stitch with this needle, then I randomly pick another needle and last the final needle (and this variable greatly increases but I missed that day in math class.). I have no idea which is which (well I do but I don’t pay any attention and just stitch). I continue to do this throughout the piece. And I also vary the placement of the stitches so a pattern does not develop.
Okay, Math class is over and I need to get back to stitching the background. For this background I chose a four way continental stitched over 2 threads…I wanted an open background that would allow the painted background to interact with the thread. I didn’t want to lay every thread and so I borrowed a technique from Cross Stitcher’s, “Railroading.” Railroading is where you place the needle between two plies as you return the needle to the back of the canvas. I have Cross Stitch friends who can do this with any amount of even plies (2-4-6) but I can only do it successfully with two ply and usually on longer stitches. You can see the technique in the picture.
Hopefully next week will have it finished and then need to decide if I am tackling the finishing or sending it to my trusty finisher…Part of me wants to learn to do this and another part of me says you traded that sewing machine for a laptop and stitching. How many of you tackle your own finishing?
Thank you for stopping by today and I hope you have time to stitch everyday! ttfn…sue